From the Workshop

November 30, 2015

Window to my workshop No 99

Filed under: No 984 — Tags: , , — admin @ 10:52 am

LEVER CAP

As with many of my components these are fabricated from solid bar. The three pictures shown below are starting from a raw bar, removing the excess and shaping then the finished product.

 

CI3A2423
 
CI3A2495
 
CI3A2511

 

This has probably been one of the most labour intensive of all the parts. Now that they are done, with the exception of polishing (which is no mean feat), I am very happy to move on to the thumb wheel and pressure pad.
 
Update: A modification has been made for ergonomic purposes. An additional chamfer has been added in case there is any contact with fingers or knuckles.
 
CI3A2522
 
CI3A2521

November 2, 2015

Window to my workshop 98

Filed under: No 984 — Tags: , , , — admin @ 5:41 pm

The pictures don’t do justice to the time spent on every little operation. Although I have taken many photographs along the way I don’t have time to document every little stage. The effort for every detail can seem a bit over the top, and I make little revisions all the time – the overall design will still be as the posted line drawing.

This is a nail biting moment, once I start cutting there is no going back. I can take hours double checking before I separate the toe from the the rest of the sole.

 
 

Holtey No 984 pic 7

 
Here I am milling the blade bed. The rest of this operation hasn’t been photographed as I covered this in the No 983 blog and it is almost identical as are the adjuster recesses. You can see that the work holding vice jaws are purpose made just for this plane. This enables me to get a firm grip.
 

Holtey No 984 pic 8

 

 

Holtey No 984 pic 9

 
All my buns start off as a true square block. All drilling, tapping and recessing is carried out on the mill
 

 
Holtey No 984 pic 10

 

Holtey No 984 pic 11
 

The bush shown here is to be epoxied into the front bun. You can use some imagination as to how I arrived here. The combined strength of the bush and its bun is considerable. Note there are two flats which make it impossible to remove the bush once the epoxy has cured.
 

Holtey No 984 pic 12

 
This is the milling operation for the five integral pins/rivets to the bun boss.
 
Holtey No 984 pic 13

 
This is the finished boss for the front bun. I have chosen this method of fixing for its strength. I wasn’t happy about tapping blind holes. Who cares, it is not about cost :-) It is going to be the only one of its kind.

 
Holtey No 984 pic 14

 
Illustrating the fitting of the bush to the bun and the threaded nose to fit the finished bun to its boss.
 

Holtey No 984 pic 15

 
Once this is complete, the bun can be removed and the boss is ready to rivet in place. Note that I used a V joint between the boss and the knob base. The knobs will leave my workshop perfect but the rotary position of the knob can have a tendency to migrate and wood can lose its concentricity over time. Also when the knob is removed and refitted the sharp edges can be bumped, thus losing the desired effect. The V joint will hide any of these unsightly dinks.
 

Holtey No 984 pic 16

 
Temporarily assembled plane.
 
 

A general selection of knobs and parts.

 
Holtey No 984 pic 17
 

 
Holtey No 984 pic 18
 
Holtey No 984 pic 19

 

Still a long way to go, sorry to those who have a plane on order.
 
 

Thought this was worth a picture and mention. The bushing here had been cemented with epoxy and I had started it with a few threads and then I was distracted ………

I discovered how strong this system is when I came back the next day. I will keep this as a reminder.

No 984 cockup

Powered by WordPress